CANON DR 9080C MANUAL PDF
December 21, 2019 | by admin
View and Download Canon DRC service manual online. DRC Scanner pdf manual download. Also for: Dr free pdf instructions. Find the office and computer equipment manual you need at ManualsOnline. Canon DRC Scanner User Manual. Page 1. Page 2. Chapter 5. Other Functions. Setting in the User Mode. You can select the mode of operation (user mode) for the scanner from those listed below. ○ Operation.
|Published (Last):||25 April 2012|
|PDF File Size:||11.47 Mb|
|ePub File Size:||13.32 Mb|
|Price:||Free* [*Free Regsitration Required]|
Page 36 Front reading unit Front platen roller Back reading unit Upper reading roller Document tray Lower reading roller Ultrasonic receiving sensor Back platen roller Ultrasonic transmitting sensor Fig.
20 Most Recent Canon DRC Path-Through Scanner Questions & Answers – Fixya
Place the inserted tip into the hole on the right side of the machine. Shading solenoid Upper Activating the shading plate of the back reading side unit. Insert the snap band attached to the cable assembly of the IP carriage into the hole located at the center of the main body upper frame. Answered on Dec 31, Chapter 2 Preparation Before Use Preparing for Paper Feed and Eject Pull out the document tray extension and the document eject tray extension to match the size of the document being scanned.
You might as well clean the metal box out, check the plastic gears, make sure the motor is plugged in, and regrease the plastic gears if they look like they need it.
I Do not turn OFF the scanner or remove any interface cables when an application is running. Page 41 Document curl must be 3 mm or less in height and the documents cannot be creased. Do not use the imprinter in the Count Only mode default.
Lift up the upper scanner slightly. Any obstruction is treated as P00 error. Page Short Insert the longer convex tip of the IP shaft into the hole inside the right side of the main body.
I Be careful when you clear a paper jam.
CANON DRC SERVICE MANUAL Pdf Download.
They are replaced by the user or service technician. Screw Retard motor Fig.
Page Confirm the following component parts. Make sure that you have everything.
See your browser’s documentation for specific instructions. The power to the scanner is ON when you are cleaning the shading plates so be very careful.
Place the document face up in the document tray, aligning the document’s top edge against the back of the document tray.
Be sure to log on as an administrator if your system is Windows NT 4. When scanning ends, the document tray is lowered. For details, refer to the user’s manual. High level accuracy staple detection.
imageFORMULA DR-9080C Color Production Scanner
Page Document guide width sensor Spacer Fig. Detect double feed in the Count Only mwnual. Drivers Software Firmware Utilities Loading If a SCSI hard disk is mounted, do not use 0 and 1. Image Troubleshooting Reading unit Is the problem solved when the End. Digital signal manuaal Without error diffusion processing With error diffusion processing Fig. Page 31 This configuration enables the unit Upper reading Front reading unit roller Back platen roller Reading glass Document Reading glass Front platen roller Back reading unit Lower reading roller Fig.
Insert the one that a tip caonn long. Use the endorser in the check mode default. Check every item you have removed from the box. If it tajes a few seconds. For others, refer to the driver software “Help”.
Canon imageFORMULA DR-9080C
Chapter 6 Troubleshooting When the Scanner Is Not Recognized The following describes possible causes of your computer not recognizing the scanner.
Automatic Feeding Chapter 4 Document Feeding and Scanning N Automatic Feeding To use er automatic feeding mode, after you instruct the scanner to start scanning from the application, the scanner will start scanning as soon as it detects a document in the document tray.
U Use the imprinter in the Count Only mode. I Be sure that the hook is completely latched and the roller cover is not loose. Chapter 4 Document Feeding and Scanning This chapter describes precautions regarding documents that can be handled on this scanner and scanning operations. Don’t have an account? Close the document eject tray extension if it is open.
Count Only Mode Chapter 4 Document Feeding and Scanning Count Only Mode In the count only mode, the documents are fed through the scanner and the number of the sr is only counted, they are not scanned. Controls the feed system and image processor.
Low level accuracy staple detection. Adjust the Delivery drive roller tension so that the belt does not miss the Fig.