APS997C INSTALLATION MANUAL PDF

February 5, 2020   |   by admin

Model APSC. Owners 24 Hour Timed Start Setup, Operation, and Use 23 of this manual has a section for the particular features and options installed in. Save this Book to Read prestige apsc installation manual PDF eBook at our Online Library. Get prestige apsc installation manual PDF. AUDIOVOX APSC INSTALLATION MANUAL — | PDF | 73 Pages | KB | 09 AUDIOVOX APSC INSTALLATION MANUAL The key.

Author: Bazahn Tojagis
Country: Iran
Language: English (Spanish)
Genre: Automotive
Published (Last): 5 April 2013
Pages: 183
PDF File Size: 17.77 Mb
ePub File Size: 8.18 Mb
ISBN: 954-3-73942-555-4
Downloads: 63294
Price: Free* [*Free Regsitration Required]
Uploader: Fenrizahn

If there is a Non Plug in Shock Sensor used with the alarm system and it is not shunted during the Remote Start activation period, then vibration from the running vehicle can cause the alarm to trigger.

By pressing ‘print’ button you will print only installattion page. To print the manual completely, please, download it. The Superheterodyne Receiver Antenna Assembly provided with this unit allows routing from below the dash board for maximum operating range. Starter Output ,anual consideration for the connection of this wire must be made to prevent the vehicle from starting while in gear.

PRESTIGE APSC INSTALLATION MANUAL Pdf Download.

Fuses must be used and istallation as close as possible to the power source for adequate protec- tion of the vehicle. The transmitters are pre-programmed from the factory, If you find you need to program new or additional transmitters follow the instructions below. Ignition 2 Output Connect this wire to the ignition 2 wire from the ignition switch.

This is accomplished by first mapping out the firing order of the engine in groups of as indicated below. Be certain that the chosen mounting location will not inhibit any of the controls of the vehicle. PART Select a mounting location inside the passenger compartment up behind the dashboard. Draw a circle around any of the columns. Once activated, the unit will start 1 time if the vehicle temperature reaches “0 ” and then will run the allotted time.

  LOS ATRIDAS PDF

Platinum APS-997C Installation Manual

Page 16 These applications require the use of additional components which may include relays, fixed resistors, or for convenience, a Door Installstion Interface.

Enter text from picture: This wire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and connect to the negative side of the ignition coil.

Parking Light Flasher Output This wire is the normally open contact of the on board parking light flash relay. Connect this wire to the vehicle’s parking light feed wire. Choose a location above the belt line dashboard of the manua, for best aaps997c. When completing an installation using either of the following key in sensor circuits, if the operator inserts the ignition key while the vehicle is running under the control of the Remote Start, the vehicle will shut down.

To connect to the key in sensor circuit as shown for method 2: Enter text from picture: This unit has the ability to learn the dome light delay time, up to 60 seconds. Tachometer Input Signal This wire will continually monitor the engine’s tach rate while the unit is under power of the Remote Start module.

Connect the Red wire to the low current 12 volt signal wire from the factory door unlock switch to the factory door unlock relay. Page of 28 Go.

Prestige APS-997C Installation Manual

Ground Output While Running – mA This wire provides a mA ground output that becomes active 3 seconds before the Remote Start Unit nistallation and remains grounded while running plus an additional 4 seconds after the Remote Start Unit turns off. If the vehicle’s parking lights are ground switched, connect this wire to chassis ground. Page 24 To connect to the key in sensor circuit as shown for method 2: Special considerations must be made for windshield glass as some newer vehicles utilize a metallic shielded window glass that will inhibit or restrict RF reception.

Failure to connect this wire to the ignition switch side mmanual the of the neutral safety switch can result in personal injury and property damage.

  ENNIO NIMIS KRIYA YOGA PDF

Parking Light Flasher Feed This wire is the common contact of the on board parking light flasher relay. Page 10 12 White Wire: If the vehicle’s parking lights are ground switched, connect this wire to mmanual ground.

Aps c Installation Manual

The following two circuits may be used only if the above circuit is not available. Monitoring The Vehicle’s Engine: The unit will monitor the voltage level of the battery during remote start, wait for the voltage to drop while cranking, then look for the voltage level to go above the level it was before the vehicle began to crank which indicates the vehicle is running.

The following procedure must be performed after the installation of any Remote Start Device. For technical support go to www.

Page 29 b 29 of When selecting Diesel operation, Bank 3 Feature 11over gasoline, the only change is to the ignition circuits. In most cases, the Purple wire will need to be connected to only one door switch no matter how many doors the vehicle has as most door lighting circuits are wired in parallel.

These modules are used to access a variety of features in the vehicle which can be as simple as door trigger inputs, to more complex door locks outputs, or transponder interfaces for remote starting. In this case, connect the Light Blue Wire to terminal 86 of a external relay.

Add to my manuals Add. Pressing the pre-programmed transmitter button s will access channel four and will remain active, for up to 20 seconds, as long as the transmitter button s is held. Shock Sensor By Pass: